Microscan MS-2 Uživatelský manuál Strana 72
- Strana / 125
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
5-10 MS-2 CCD Reader User’s Manual
Code 128/EAN 128
Code 128/EAN 128
Minimum Symbol Length (Code 128/EAN 128)
Application Record Separator Character
(Code 128/EAN 128)
Usage: Code 128 is a smaller symbology useful in applications with limited space
and high-security requirements.
Definition: A very dense alphanumeric symbology. It encodes all 128 ASCII characters,
it is continuous, has variable length, and uses multiple element widths
measured edge to edge.
Serial Cmd:
<
K474,
status
,0,minimum symbol length,1
,1,0,
application record separator
character>
Default: Disabled
Options: 0 = Disabled 1 = Enabled
Usage: Minimum Symbol Length helps prevent truncations and increases data
integrity by ensuring that only one symbol length will be accepted.
Definition: This specifies the exact number of characters that the reader will recognize
(this does not include start, stop, and check characters). The reader
ignores any symbol not having the specified length.
Serial Cmd:
<
K474,
status
,0,
minimum symbol length
,1
,1,0,
application record separator
character>
Default: 0
Options: 0 to 32
Definition:
This is an ASCII character that serves as a separator in formatted output.
Serial Cmd: <
K474,
status
,0,minimum symbol length,1
,1,0,
application record separator
character>
Default:
NUL
Options:
Any ASCII character (7 bit)
- MS-2 CCD Reader 1
- User’s Manual 1
- Disclaimer 2
- Latest Manual Version 2
- Technical Support 2
- What Is Covered? 3
- What Is Excluded? 3
- Limitation of Liability 3
- Table of Contents 4
- About the MS-2 CCD Reader 6
- About This Manual 6
- Highlighting 6
- Host Communications 6
- Warning and Caution Summary 7
- Statement of RoHS Compliance 9
- MS-2 CCD Reader User’s Manual 10
- 1 Quick Start 11
- Step 1 — Check Hardware 12
- Step 2 — Connect the System 13
- Step 3 — Install ESP 14
- Step 4 — Select Model 15
- Step 5 — Autoconnect 16
- Step 6 — Position the Reader 17
- Step 7 — Configure the Reader 18
- Saving Options 19
- Save Configuration in ESP 20
- 2 Using ESP 21
- Application Mode 23
- Menu Toolbar 24
- Preferences > General Tab 26
- Preferences > Terminal Tab 27
- Sizing Information 28
- Preferences > Advanced Tab 29
- (cont.) 30
- Connect to Readers via TCP/IP 30
- Use Default Storage Location 30
- Document Memo 31
- Model Memo 31
- Autoconnect 32
- Autoconnect (cont.) 33
- Navigating in ESP 35
- Send/Receive Options 36
- Defaulting 37
- Advanced Options 37
- 3 Communications 39
- Communications by ESP 40
- Host Port Connections 42
- Host Port Protocol 43
- Preamble 44
- Postamble 45
- 4 Read Cycle 47
- Read Cycle by ESP 48
- Read Cycle Serial Commands 49
- MS-2 Read Cycle Overview 50
- Number of Symbols 51
- Trigger Mode 53
- External Edge 54
- Serial Data 54
- Serial Data and Edge 54
- No Decode Timeout 59
- Decodes Before Output 60
- No Read Message 61
- Reader Setup 62
- 5 Symbologies 63
- Symbologies by ESP 64
- Symbologies Serial Commands 65
- Full ASCII Set (Code 39) 67
- Symbol Length (Codabar) 69
- Interleaved 2 of 5 70
- Minimum Length 71
- Fixed Length 71
- Code 128/EAN 128 72
- GS1 DataBar (RSS) 74
- MSI Code 75
- Plessey Code 76
- Industrial 2 of 5 77
- UPC-A Status (UPC/EAN) 79
- UPC-E Status (UPC/EAN) 79
- EAN-8 Status (UPC/EAN) 79
- EAN-13 Status (UPC/EAN) 80
- UPC-A as EAN-13 (UPC/EAN) 81
- UPC-E as UPC-A (UPC/EAN) 81
- EAN-8 as EAN-13 (UPC/EAN) 81
- Symbology Identifier 82
- Terminal 83
- Terminal Window 84
- Editing a Macro 87
- Terminal Window Menus 88
- Utilities 89
- Serial Utility Commands 90
- Differences from Default 91
- Firmware 92
- Firmware Verification 94
- Device Control 95
- Default/Reset/Save 96
- Reader Status Request 97
- General Specifications 100
- MS-2 CCD Reader Dimensions 100
- Appendices 101
- Serial Configuration Commands 104
- Serial Command Format 105
- Appendix E — ASCII Table 108
- Appendix F — Operational Tips 109
- 5 Volt Devices 110
- 10-28 Volt Devices 110
- Hyperlink Index 115
- Variable Length 124
- Very Large-Scale Integration 124
- Warranty 124
- Recipient Response 125
Související produkty a manuály pro Čtečky čárových kódů Microscan MS-2
Čtečky čárových kódů Microscan HE45T Uživatelský manuál
(102 stránky)
(102 stránky)
Čtečky čárových kódů Microscan MS-4Xi Uživatelský manuál
(360 stránky)
(360 stránky)
(2 stránky)
Čtečky čárových kódů Microscan MS-4X Uživatelský manuál
(312 stránky)
(312 stránky)
Čtečky čárových kódů Microscan HS-51X Uživatelský manuál
(156 stránky)
(156 stránky)
Čtečky čárových kódů Microscan MS-4X Uživatelský manuál
(374 stránky)
(374 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.132 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce