Microscan HS-2D Uživatelský manuál Strana 96
- Strana / 172
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
7-8 HS-21/HS-41X Handheld Reader User’s Manual
Motion Detect Event
Motion Detect Event
Motion Detect Event allows you to determine the reader's behavior when motion is
detected in the field of view.
Show Target
The target LEDs will illuminate when a motion detect event occurs.
Read Both Fields (Default)
Both Near Field and Far Field will be activated to capture an image when a motion detect
event occurs.
Read Near Field
Near Field will be activated to capture an image when a motion detect event occurs.
Read Far Field
Far Field will be activated to capture an image when a motion detect event occurs.
Read Primary Field
When Read Primary Field is selected, the most recent field to have produced a Good
Read (Near Field or Far Field) will be activated to capture an image when a motion detect
event occurs.
Read the configuration symbols below to enable or disable Motion Detection.
Motion Sensitivity
allows you to determine
the sensitivity of motion
detection (lower is more
sensitive - 5 is default).
Motion Detect Start
Delay allows you to set
the amount of delay
before a motion detect
event occurs. (0 seconds
is default.)
Motion Detection On
Start Delay 0
Motion Detection Off
Motion Detection On,
Start Delay 500 ms
- HS-21/HS-41X Handheld Reader 1
- User’s Manual 1
- Disclaimer 2
- Latest Manual Version 2
- Technical Support 2
- What Is Covered? 3
- What Is Excluded? 3
- Limitation of Liability 3
- Table of Contents 4
- Introduction 5
- Highlighting 6
- About This Manual 6
- Statement of RoHS Compliance 8
- 1 Quick Start 9
- Check Required Hardware 10
- USB Interface 11
- RS-232 Interface 12
- Install ESP 13
- Select Model 14
- Click the Show 16
- Connect Symbol 16
- Configure the Reader 17
- Save Changes in ESP 18
- 2 Using ESP 19
- Application Mode 21
- Tree Controls 22
- Menu Toolbar 23
- New Model 24
- Preferences > General Tab 25
- Preferences > Terminal Tab 26
- Sizing Information 27
- Preferences > Advanced Tab 28
- Use Default Storage Location 29
- Document Memo 30
- Model Memo 30
- Connection Wizard 31
- Bar Code Dialog 32
- Send/Receive 33
- Default Current Menu Settings 34
- Default all ESP Settings 34
- Advanced Options 34
- 3 Basic Operations 35
- Practice Targeting 36
- Motion Detect Mode 37
- Dual Optics 38
- Dual Optics Examples 39
- Operational Feedback 40
- 4 Communications 41
- Communications by ESP 42
- Communications Overview 43
- Parity (RS-232) 46
- Data Bits (RS-232) 46
- Preamble 47
- Postamble 48
- Preamble and Postamble by ESP 49
- Keyboard Mapping 50
- Communications Mode 51
- Text Commands 52
- Text Commands by ESP 52
- USB Keyboard Rate 53
- Baud Rate 54
- Stop Bits 54
- Data Bits 54
- Text Command Timeout 55
- 5 Read Cycle 57
- Read Cycle by ESP 58
- External Trigger 59
- Default Continuous Event 60
- Maximum Decodes per Read 61
- Read Cycle Timeout 62
- Read Cycle 63
- Targeting Zone Tolerance 64
- Morphological Preprocessing 65
- Camera Settings 66
- 6 Symbologies 69
- Symbologies by ESP 70
- Data Matrix 71
- Symbologies 73
- Sample Aztec Symbol 73
- Code 39 74
- Code 128 75
- Sample BC412 Symbol 76
- Code 93 77
- Codabar 78
- Interleaved 2 of 5 79
- Pharmacode 82
- GS1 DataBar 84
- Sample PDF417 Symbol 85
- MicroPDF417 86
- Composite 87
- Symbology Identifier 88
- 7 I/O Parameters 89
- I/O Parameters by ESP 90
- No Read Notification 91
- Targeting 92
- Button Stay-Down Time 95
- Motion Detect Event 96
- Image Quality 97
- 8 Advanced Operations 99
- Continuous Read 100
- Mirroring 101
- Motion Detection 102
- Window of Interest 103
- Linear Mode 104
- Terminal 105
- Terminal View 106
- Editing a Macro 109
- Terminal Right-Click Menu 110
- Terminal Dropdown Menu 111
- 10 Utilities 113
- Device Control 114
- Differences from Default 115
- Firmware 116
- ID and Firmware Version 117
- Advanced 118
- Appendices 119
- General Specifications 120
- USB Cable Pinouts 123
- RS-232 Cable Pinouts 123
- Configuration Symbols 124
- Appendix D — Serial Commands 135
- Packetized Commands 136
- Command Types 138
- Simple Protocol 142
- Reader Settings 143
- Binary Dip Switch 144
- Field of Interest 144
- Reader Settings Table 145
- Serial Commands 146
- CRB System 163
- Example CRC16 C Code 163
- Communications Protocol 166
- Appendix F — ASCII Table 167
- Appendix G — Maintenance 168
Související produkty a manuály pro Čtečky čárových kódů Microscan HS-2D
Čtečky čárových kódů Microscan MS-2 Uživatelský manuál
(125 stránky)
(125 stránky)
Čtečky čárových kódů Microscan HE45T Uživatelský manuál
(102 stránky)
(102 stránky)
Čtečky čárových kódů Microscan MS-4Xi Uživatelský manuál
(360 stránky)
(360 stránky)
(2 stránky)
Čtečky čárových kódů Microscan MS-4X Uživatelský manuál
(312 stránky)
(312 stránky)
Čtečky čárových kódů Microscan HS-51X Uživatelský manuál
(156 stránky)
(156 stránky)
Čtečky čárových kódů Microscan MS-4X Uživatelský manuál
(374 stránky)
(374 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.210 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce