Microscan MS-2 Uživatelský manuál Strana 55
- Strana / 125
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
MS-2 CCD Reader User’s Manual 4-9
Read Cycle
Continuous Read 1 Output Emulation
Setting Up Continuous Read 1 Output Emulation
1. Set Number of Symbols to Multiple.
2. Set Time Between Identical Decodes to 500 (ms).
3. Set Trigger Mode to External Level.
Important: Continuous Read 1 Output Emulation is not recommended for automated
environments, because there is typically no reliable way to verify whether or not a symbol
was missed.
Usage: Continuous Read 1 Output can be useful in applications where it is not
feasible to use a trigger and all succeeding symbols contain different
information. It is also effective in applications where the objects are presented
by hand.
The MS-2 does not offer this feature, but it can be emulated by following
the steps described below.
Definition: In Continuous Read 1 Output Emulation, the trigger must be active
(grounded) for as long as the MS-2 needs to be scanning symbols. The
MS-2 will only output symbol data once while that symbol remains in the
MS-2’s field of view. If the symbol is removed and then presented again, it
must be removed from the field of view for the amount of time specified in
the Time Between Identical Decodes value before the MS-2 will decode
the symbol again. However, if a new symbol is presented, the MS-2 will
decode it and output symbol data immediately.
Serial Cmd: <K222,0>
Serial Cmd: <K503,500>
Serial Cmd: <K200,2>
- MS-2 CCD Reader 1
- User’s Manual 1
- Disclaimer 2
- Latest Manual Version 2
- Technical Support 2
- What Is Covered? 3
- What Is Excluded? 3
- Limitation of Liability 3
- Table of Contents 4
- About the MS-2 CCD Reader 6
- About This Manual 6
- Highlighting 6
- Host Communications 6
- Warning and Caution Summary 7
- Statement of RoHS Compliance 9
- MS-2 CCD Reader User’s Manual 10
- 1 Quick Start 11
- Step 1 — Check Hardware 12
- Step 2 — Connect the System 13
- Step 3 — Install ESP 14
- Step 4 — Select Model 15
- Step 5 — Autoconnect 16
- Step 6 — Position the Reader 17
- Step 7 — Configure the Reader 18
- Saving Options 19
- Save Configuration in ESP 20
- 2 Using ESP 21
- Application Mode 23
- Menu Toolbar 24
- Preferences > General Tab 26
- Preferences > Terminal Tab 27
- Sizing Information 28
- Preferences > Advanced Tab 29
- (cont.) 30
- Connect to Readers via TCP/IP 30
- Use Default Storage Location 30
- Document Memo 31
- Model Memo 31
- Autoconnect 32
- Autoconnect (cont.) 33
- Navigating in ESP 35
- Send/Receive Options 36
- Defaulting 37
- Advanced Options 37
- 3 Communications 39
- Communications by ESP 40
- Host Port Connections 42
- Host Port Protocol 43
- Preamble 44
- Postamble 45
- 4 Read Cycle 47
- Read Cycle by ESP 48
- Read Cycle Serial Commands 49
- MS-2 Read Cycle Overview 50
- Number of Symbols 51
- Trigger Mode 53
- External Edge 54
- Serial Data 54
- Serial Data and Edge 54
- No Decode Timeout 59
- Decodes Before Output 60
- No Read Message 61
- Reader Setup 62
- 5 Symbologies 63
- Symbologies by ESP 64
- Symbologies Serial Commands 65
- Full ASCII Set (Code 39) 67
- Symbol Length (Codabar) 69
- Interleaved 2 of 5 70
- Minimum Length 71
- Fixed Length 71
- Code 128/EAN 128 72
- GS1 DataBar (RSS) 74
- MSI Code 75
- Plessey Code 76
- Industrial 2 of 5 77
- UPC-A Status (UPC/EAN) 79
- UPC-E Status (UPC/EAN) 79
- EAN-8 Status (UPC/EAN) 79
- EAN-13 Status (UPC/EAN) 80
- UPC-A as EAN-13 (UPC/EAN) 81
- UPC-E as UPC-A (UPC/EAN) 81
- EAN-8 as EAN-13 (UPC/EAN) 81
- Symbology Identifier 82
- Terminal 83
- Terminal Window 84
- Editing a Macro 87
- Terminal Window Menus 88
- Utilities 89
- Serial Utility Commands 90
- Differences from Default 91
- Firmware 92
- Firmware Verification 94
- Device Control 95
- Default/Reset/Save 96
- Reader Status Request 97
- General Specifications 100
- MS-2 CCD Reader Dimensions 100
- Appendices 101
- Serial Configuration Commands 104
- Serial Command Format 105
- Appendix E — ASCII Table 108
- Appendix F — Operational Tips 109
- 5 Volt Devices 110
- 10-28 Volt Devices 110
- Hyperlink Index 115
- Variable Length 124
- Very Large-Scale Integration 124
- Warranty 124
- Recipient Response 125
Související produkty a manuály pro Čtečky čárových kódů Microscan MS-2
Čtečky čárových kódů Microscan HE45T Uživatelský manuál
(102 stránky)
(102 stránky)
Čtečky čárových kódů Microscan MS-4Xi Uživatelský manuál
(360 stránky)
(360 stránky)
(2 stránky)
Čtečky čárových kódů Microscan MS-4X Uživatelský manuál
(312 stránky)
(312 stránky)
Čtečky čárových kódů Microscan HS-51X Uživatelský manuál
(156 stránky)
(156 stránky)
Čtečky čárových kódů Microscan MS-4X Uživatelský manuál
(374 stránky)
(374 stránky)
Impulse Hardware manuali utente
Partendo da T
Komentáře k této Příručce